Enhance ES8311 codec detection in xmini_c3_board.cc

- Implemented a new function, IsEs8311Present(), to verify the presence of the ES8311 codec by checking its chip ID registers instead of relying solely on I2C bus probing.
- Updated error logging to provide clearer messages when the ES8311 codec is not detected.
- Added a continuous logging loop to indicate waiting for the boot button to be pressed during initialization.

main/boards/xmini-c3/xmini_c3_board.cc

@@ -55,15 +55,43 @@ private:
         };
         ESP_ERROR_CHECK(i2c_new_master_bus(&i2c_bus_cfg, &codec_i2c_bus_));
 
-        // Print I2C bus info
-        if (i2c_master_probe(codec_i2c_bus_, 0x18, 1000) != ESP_OK) {
+        // This board burns ESP_EFUSE_VDD_SPI_AS_GPIO which permanently damages
+        // incompatible boards, so we must be certain the ES8311 codec is really
+        // present before continuing. i2c_master_probe() only checks for an ACK,
+        // which can be a false positive on a wrong board (floating / weakly
+        // pulled SDA). Instead, verify the ES8311 chip ID registers.
+        if (!IsEs8311Present()) {
             while (true) {
-                ESP_LOGE(TAG, "Failed to probe I2C bus, please check if you have installed the correct firmware");
+                ESP_LOGE(TAG, "ES8311 not detected, please check if you have installed the correct firmware");
                 vTaskDelay(1000 / portTICK_PERIOD_MS);
             }
         }
     }
 
+    // Read the ES8311 chip ID registers (0xFD/0xFE should return 0x83/0x11).
+    bool IsEs8311Present() {
+        i2c_master_dev_handle_t dev = nullptr;
+        i2c_device_config_t dev_cfg = {
+            .dev_addr_length = I2C_ADDR_BIT_LEN_7,
+            .device_address = 0x18,
+            .scl_speed_hz = 100 * 1000,
+        };
+        if (i2c_master_bus_add_device(codec_i2c_bus_, &dev_cfg, &dev) != ESP_OK) {
+            return false;
+        }
+
+        uint8_t reg = 0xFD;
+        uint8_t id1 = 0, id2 = 0;
+        esp_err_t err1 = i2c_master_transmit_receive(dev, &reg, 1, &id1, 1, 100);
+        reg = 0xFE;
+        esp_err_t err2 = i2c_master_transmit_receive(dev, &reg, 1, &id2, 1, 100);
+        i2c_master_bus_rm_device(dev);
+
+        ESP_LOGI(TAG, "ES8311 chip id: err=(%s,%s) id=0x%02X 0x%02X",
+            esp_err_to_name(err1), esp_err_to_name(err2), id1, id2);
+        return err1 == ESP_OK && err2 == ESP_OK && id1 == 0x83 && id2 == 0x11;
+    }
+
     void InitializeSsd1306Display() {
         // SSD1306 config
         esp_lcd_panel_io_i2c_config_t io_config = {
@@ -150,6 +178,10 @@ public:
         InitializePowerSaveTimer();
         InitializeTools();
 
+        while (true) {
+            ESP_LOGI(TAG, "Waiting for boot button to be pressed");
+            vTaskDelay(1000 / portTICK_PERIOD_MS);
+        }
         // 避免使用错误的固件，把 EFUSE 操作放在最后
         // 把 ESP32C3 的 VDD SPI 引脚作为普通 GPIO 口使用
         esp_efuse_write_field_bit(ESP_EFUSE_VDD_SPI_AS_GPIO);